Loudspeaker components Loudspeaker
Coils Introduction Coils
Coils sorted by inductivity Coils sorted
by inductivity
Audaphon coils Audaphon
Mundorf air coil Mundorf
air coil
Baked varnish air coil Baked varnish
air coil
Hepta Strand coil Hepta
Strand coil
Mundorf CFC coil Mundorf
CFC coil
Mundorf VLCU coil Mundorf
VLCU coil
Silver/gold air coils Silver/gold
air coils
Aronit / P core coil Aronit / P
core coil
Drum / H core coil Drum / H
core coil
i-core coil/ BS coil i-core coil/
BS coil
Transformer core coil Transformer
core coil
Zero Ohm Coil Zero Ohm
Duelund coils Duelund
Jantzen Wax coils Jantzen Wax
Visaton coils Visaton
more infos on coils more infos
on coils
Coilcalculator Coil-



Dr.-Ing. Peter Strassacker
E-mail: info@lautsprechershop.de
further pages: range of coils

Like capacitors, all coils represent an energy storage.

Coil Calculator

The coil consists of a wound conductor. Usually copper wire is wound around a synthetic core. When current flows through the conductor a magnetic field is generated. This field holds energy. The more windings a coil has and the bigger its diameter, the bigger the stored energy - at a given current.

How is stored energy specified?

The coil's stored energy E is dependant on the coil's inductance L and the current I applied squared. E = 0.5*L*I2. The higher the inductance L , the more energy the coil stores - at given current. The unit of measure is Henry or H, where usually only a thousandth is needed: Millhenry or mH.

What are the implications for loudspeakers?

When current is applied to a coil, a magnetic field proportional to the current is generated around the conductor. In order to build-up a magnetic field a voltage in the coil is needed. If not enough voltage is available, the magnetic field is built-up slowly. The current flow through the coil also rises only slowly. In other words: The current in the coil is linked to a magnetic field; voltage applied ensures a slow rise of both. When the current changes, the coil charges or discharges. Again, a voltage is applied to the coil, delaying the current change. If a loudspeaker is connected to the coil in series, the coil delays at quick voltage changes. For high frequencies the coil needs all available voltage to recharge - nothing is passed on anymore to the loudspeaker.

When a coil is connected in parallel to a loudspeaker something else happens. At quick current / voltage changes the coil changes its magnetic field and lets the AC voltage pass through. The coil works like a filter, letting high frequency oscillation pass through to the loudspeaker connected in parallel.

What is the ideal coil?

An ideal coil shows above mentioned properties. Ideally a coil stores energy while not dissipating any - therefore, the coil doesn't generate any heat. However, in reality no electrical component is perfect. The wires of a coil are not infinitely good conductors , that's the reason why energy is turned into heat. Additionally, losses occur when a coil recharges, especially when electrical conductors (eddy-current losses) or magnetically active material (magnetic snapback) are close by.

What types of coils are available and what properties do they have?

There are air core coils and coils with magnetic core. The latter are divided into coils with open or closed core around the wire-wrap. The list of coils in ascending order of quality:

When to use which coil?

The following table lists the typical properties of coils:
Coil type typical loss
(f=1kHz and 20 C)
size cost PA application standard application high-end application saturation inductance B
air core coils

far superior to all other coils regarding impedance response, vibration and microphonics effect: the foil coil by Mundorf

small large medium parallel to tweeter parallel to tweeter in series to bass driver or in parallel to tweeter       -
Coils with iron based materials
(transformator core, BS core)
? small low in series to bass driver or in parallel to tweeter impedance correction     - 2.3 Tesla
Coils with ferrite based materials
(Mundorf H-core)
? medium medium in series to bass driver or in parallel to tweeter in series to bass driver or in parallel to tweeter impedance correction0.5 Tesla

Additional important notes: If a crossover is optimised for a high-impedance coil, the use of a low-impedance coil often doesn't show any advantage. The crossover needs to be tuned again incorporating the high quality component. A re-tuning is also advisable when exchanging a coil with core for a coil without core; since distortion is reduced the result would be rather positive.

What resistance does the ideal coil have?

A coil's resistance is frequency dependant. This resistance cannot be compared with the common resistance. For an estimate the calculation of reactance is quite helpful.
Z = 2*π*frequency*L)
where L=inductance, f=frequency, Pi=3.141...


Coil Calculator

for f=100 Hz and L=1mH (m represents a thousandth):
Z = 6.28 * 100 Hz * 0.001 H = 0.628 Ohm